Your Plumbing Crash Course: A Necessity for Bathtub Installation
Your Plumbing Crash Course: A Necessity for Bathtub Installation
Blog Article
The article author is making a number of great observations about How to Install a Bathtub overall in the article below.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is readily available, the task can relocate easily; if you need to open up a wall surface to get rid of the old tub and place the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the job and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed job, it is far better to take into consideration utilizing one before you start. Chances are you may need a professional plumber to make tube links.
This short article will certainly help you mount a brand-new bathtub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools and also product list need to comprise the following:
Planning for the Installment
First of all, the supporting structure supplied with the bath must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, place the bathtub in the needed placement. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four small points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the tub until the level checks out degree.
To install faucets, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Activate the water and examine all joints as well as new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the tub needs to wait until the bathtub has actually been used at least when as this will resolve it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the tap as well as the sink. Safeguard the tap in place with the producer provided backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type should be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with moisture as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can split rather very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that write up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the web. Sharing is caring. Helping people is fun. Thanks a bunch for your time. Come back soon.
Maintain plumbing standards; contact us. Report this page